Florian 's issue had nothing to do with keyer modes. He tried CW Decoder when he should have used CW Keyer. Curtis, Ultimatic etc are usually referred to as keyer modes; the only real overload is stra

#morserino #issues

Keyer Mode is one of Straight Key | Non-Squeeze | Ultimatic | Curtis B | Curtis A I also found that slightly confusing... this is slightly overloaded If you read it as "Keyer Input" rather than "Keyer

#morserino #issues

hello - i think there are two differnt things : the keyer curtis modes and straight key or paddle ... Send via my cell phone Am 15.01.2023 um 19:01 schrieb Florian <flogab@...>:

#morserino #issues

Yes, you are right. I was using CW decoder mode. All works fine in keyer mode. Stupid beginner‘s mistake. 🫣 mea culpa

#morserino #issues

Could it be that you are using the Morserino in CW Decoder mode? That always treats the keys as straight keys... Use CW Keyer mode or echo trainer and everything should be ok. Von meinem Mobiltelefon

#morserino #issues

Hello everyone, I have an issue with the Morserino keyer mode. I have used an external straight key for a while and hence set the keyer mode to straight key. Now I want to change to an external (dual)

#morserino #issues

I figured one thing out - I wasn't saying "hi" to cq.morserino.info - so #1 is working. So, what do I send to the other 2 to get them talking? Thanks again. KK6BDF

#issues

Hi all - I have 2 M32's - both working fine. I've programmed the Wifi config on both, one to use my home network and the other to use my hotspot (iPhone) The WiFi's connect to each network as they sho

#issues

Willi, Merry Christmas to you and your family. And thank you for developing the Morserino series. I have two of them. I just packed one for my winter trek to warmer climate to brush up on my CW again…

#issues

👍 Happy holidays from Austria! 73 Willi Von meinem Mobiltelefon gesendet

#issues

Hi Willi, Today i received the new Heltec module. Fortionaly it worked in one go! Thank you for your efforts, i can now practice morse code :-) 73 André PA3EIV

#issues

Do you have the parameters set to Curtis A, Curtis B, Ultimatic, or side lever?

#morserino #issues

Hi guys, I use morserino mainly for Echo training with the supplied capacitive paddles and it works well from my point of view. But when I connect my external iambic paddles there is a long lag when I

#morserino #issues

Hi Willi, Thank you for your support! I too hope that a new Heltec module solves the problem. 73 André PA3EIV

#issues

André, It is mysterious… As a next step, I will ship you a new Heltec module - hopefully the problem will go away. 73 Willi

#issues

Hi Willi, By close inspection of the underside of the Heltec module i could not see any evidence of bad soldering of the ESP-32 chip. I made some pictures.

#issues

André, I think a software problem can be ruled out. We need to determine if the Heltec module is to be blamed. When the module is out, can you make a high resolution close-up picture of the underside

#issues

Hi Willi, Thank you for your answer. Unfortunately there is still no signal on pin 23 and no sound via speaker or headphone. The volume is turned all the way up. The indicator on the display works, an

#issues

André, Very strange. Did you test directly on the Heltec module? The tone signal should be detectable on pin 23, no matter what the volume is, except the volume has been turned to zero (make sure you

#issues

Hi All, My name is André. The day before yesterday i received my M-32 kit. Yesterday i finished the built-up directed by the manual. I am no beginner in soldering! All went well and the heltec module

#issues